20 new inventions

20 inventions that could change our world

650 projects from 18 different countries have been trimmed down to a final list of 20 inventions that promise to change our world. Here are 12 of the finalists for the 2013 James Dyson Awards. A winner will be chosen on November 7th and awarded $45,000. For the the full list of winners visit JamesDysonAward.org.
Cortex (New Zealand)
Problem: Traditional casts are heavy, clumsy, not waterproof, itchy and smelly.  In addition they cannot be recycled.

Solution: Cortex is a 3D printed cast system for fracture support. It is a lightweight, ergonomic, waterproof and ventilated support. After 3D scanning the limb a tight fitting cast is generated, with localised support in relation to the point of fracture. A strong recyclable plastic is used to reduce waste material.



Renewable Wave Power (UK)

Problem: Britain has 11,073km of coastline and the potential to produce 40-70KWh per metre, yet we harnesses less than 1% of this free, powerful resource. Current wave converters only harvest energy from waves moving on one axis, but in reality the sea and waves do not move in a predictable, linear, fashion.

Solution: RWP is a device that absorbs forces from the peaks and troughs of waves on any axis, from any direction - making it more durable and more effective.

Source: Sam Etherington/Renewable Wave Power/James Dyson Foundation

Gluco (France)

Problem: Currently diabetics use a device which breaks the skin to measure their blood sugar levels. Based on these results they adjust the level of insulin they have to inject. This can be fiddly, painful and time consuming.

Solution: Gluco uses the patient’s smartphone linked to a watch to measure their blood sugar levels. This eliminates the need to break the skin. As insulin pen takes the results from the watch and prepares the appropriate dosage. If sugar levels become too high or too low, the information is transmitted to a nominated contact.

Source: Gluco/Florian Lemaitre/James Dyson Foundation

Xarius (Germany)

Problem: If gadgets run out of battery when you are on the move it can be difficult to charge them.  Current solutions largely rely on batteries.

Solution: Xarius is a portable energy generator that allows the charging of electrical appliances using windpower – making it suitable for areas with limited access to mains electricity. It is composed of a foldable three-wing-system and an internal energy generator.

Source: David Engelhorn/Xarius/James Dyson Foundation

Titan arm (USA)

Problem: Occupational lifters such as warehouse workers face increased risk of arm and back injuries because they repeatedly lift heavy items. Those who have sustained arm or back injuries face a lengthy process to rebuild muscle and strength.

Solution: Titan arm is an upper-body exoskeleton that augments human strength. It augments the user’s arm strength to reduce fatigue, and braces the back to prevent poor lifting posture. Titan arm can also be used to help stroke and injury victims rebuild muscle and re-learn fine motor control as well as assist people who suffer from permanent injuries or disabilities.

Source: Titan arm/James Dyson Foundation

Mamori (Ireland)

Problem: In high contact sport concussion is common, but often it is difficult to ascertain whether the player requires medical attention. Undiagnosed concussion can have a significant impact on long-term health. 

Solution: Mamori is a gum shield with integrated sensors. It measures any impact on a sportsman and transmits the data to medical staff at the side of the pitch. If contact to the head reaches a certain level the medical staff are able to react quickly and appropriately. 

Source: Mark Dillon/Mamori/James Dyson Award

BioWool (UK)

Problem: The coarse wool industry creates a vast volume of waste product that mostly goes to landfill.

Solution: BioWool uses this waste material to make a biodegradable, flame resistant, biopolymer. It can be moulded into a variety of products and made with two finishes: one similar to plastic, the second hard on one side and soft like felt on the other. The material is made by carding the wool and then using needles to shred and pull the fibres together. After this a bio-resin is added to create a polymer that can be shaped and moulded.

Source: Dan McLoughlin/BioWool/James Dyson Foundation

Handie (Japan)

Problem: Dexterous prosthetic hands are expensive. 

Solution: Handie is an affordable prosthetic hand with inbuilt myoelectric sensors which can read brain signals. Costs have been reduced by using a smartphone to compute the electrical impulses on the skin’s surface. All components of the hand are easily modified and reproduced using a 3D printer. The hand relies on one motor that changes trajectory depending on the shape of an object.

Source: Hiroshi Yamaura/Handie/James Dyson Foundation

In Phone Post 3.0

OLTU (Spain)

Problem: Fruits and vegetables are best stored and ripened in specific conditions. The fridge is not always the optimum place to store them.

Solution: OLTU uses the excess heat produced behind the fridge to power a separate tower unit.  It contains four sections tailored to the favored conditions of different fruit and vegetables - cold dry, cold wet, fresh wet and dry warm.

Source: Fabio Molinas/OLTU/James Dyson Foundation

Roam (Australia)

Problem: Oxygen therapy is the fastest way to medically treat someone suffering from a sudden severe asthma attack. Existing oxygen cylinders are heavy (particularly for children) and expensive.

Solution: Roam is a more practical oxygen cylinder – easy to use and simple to transport. Created for young children, Roam includes an innovative nasal mask that gently rests on the users face as they breathe in oxygen.

Source: ShanShan Wang/Roam/James Dyson Foundation

Robotic Surgery: Automated Suturing Tool (Canada)

Problem: Minimally invasive surgery leads to small incisions that can be difficult to suture.

Solution: The automated suturing tool is aimed for laparoscopic surgery, invasive surgery focused on the abdominal area. Eliminating the need for manual suturing means the device can save valuable time in the operating room, save money for hospitals and free up operating rooms for other patients.

Source: Robotic Surgery: Automated Suturing Tool/Karl Price/James Dyson Foundation

Lenify (USA)

Problem: On traditional stretchers, patients must be lifted and placed onto the canvas.  Moving the patient can often cause secondary injury – sometimes worse than the initial injury.

Solution: Lenify is divided into three pieces, allowing first responders to slide head, body and leg sections under the patient in turn, minimizing how much they have to adjust the patient. It is secured by a handle locking element.

Source: Ta-Chi Lin/Lenify/James Dyson Foundation

The TeamO Back Pull lifejacket harness is designed to overcome an existing design flaw which causes many fatalities. When a person goes overboard off a ship wearing a lifejacket, attached to the vessel by a life line tether, the position of the tether on the front of the chest results in the victim being dragged through the water face down. The victim is unable to lift their head clear of the water, or move their arms in a normal manner. Life expectancy is very short. The TeamO functions like a normal lifejacket, however when a sailor goes overboard wearing a TeamO a hidden strop deploys to rotate the wearer on to their back.The victim is towed backwards with their mouth and airways clear and unobstructed.The jacket creates a ‘bow wave’ effect with the head protected from oncoming waves and they are able to use their arms normally. The strop is designed as a lifting point, making it easier to retrieve the victim using a line, reducing the risk of further injury to victim or rescuers



Where are the pocket pussies of tomorrow. Phone Post 3.0

Unlike traditional bike lights, which project light in only one direction, Revolights cast 360 degrees of illumination, making it much easier for others to sight the rider. This improves safety tremendously, as most nighttime bike-car collisions are due to inadequate side visibility. The patented Revolights bike lighting system consists of two narrow rings of LEDs that mount directly to each wheel using a series of clips and ring spacers. Lithium-ion batteries, bracket-mounted to the front and rear hub, supply power to the LEDs. The batteries are slim and lightweight, and can be charged via USB. A small, fork-mounted magnet and an integrated accelerometer provide speed and orientation data to the rings. This allows the LEDs to illuminate only when oriented at the front or rear of the bicycle.



Hydros is a three piece personal flotation device that mitigates the effects of cold water shock, sea spray, hypothermia, and secondary drowning. This is completed through a process of layering levels of clothing, exploiting the effects of hypothermia to an advantage, restricting heat loss through convection, conduction and evaporation. Utilising the wetsuit effect, and ensuring a clear airway.



Sono, from Austria, aims to cancel out certain sounds, preventing them pass through a window. Users can select which tones to eliminate via wi-fi.

In Phone Post

Comb is a design for a driverless dumper truck. The Austrian project proposes using GPS location tech to direct the vehicle, meaning it would not have to make room for a person on board.